How Much Does Concrete Cost in Ocala, FL? (2026 Price Guide)

In Ocala and Marion County, you can expect the installed cost of a standard 4-inch concrete slab to range from $9 to $18 per square foot in 2026. This price includes labor, materials, and basic site preparation. The raw material cost for ready-mix concrete delivered to your site is typically between $150 and $200 per cubic yard, but this doesn't include the significant costs of labor, forming, finishing, and site work.

Estimated Concrete Slab Costs in Ocala (Installed)

Homeowners often ask for pricing based on common project sizes. The table below shows typical installed price ranges for standard 4-inch thick concrete slabs with a broom finish in the Ocala area. Keep in mind that factors like site access, grading needs, and tear-out of old concrete can shift the final price.

Slab Dimensions	Approx. Square Feet	Approx. Cubic Yards (4" thick)	Typical Installed Price Range (2026)
10' x 10'	100 sq ft	1.25 yards	$1,200 - $2,200
12' x 12'	144 sq ft	1.8 yards	$1,600 - $2,900
16' x 20'	320 sq ft	4.0 yards	$3,200 - $5,800
20' x 20'	400 sq ft	5.0 yards	$3,800 - $7,000
24' x 24'	576 sq ft	7.1 yards	$5,200 - $9,800
30' x 30'	900 sq ft	11.1 yards	$7,650 - $15,300
40' x 60'	2,400 sq ft	29.6 yards	$19,200 - $38,400

Note: These are estimates for straightforward projects. For an exact, no-obligation price for your specific job, you need an on-site evaluation. To figure out the exact yardage your project will require, you can use our concrete calculator.

What Drives Your Final Concrete Price?

The price per square foot isn't a fixed number. It's a result of several key factors that we assess during a site visit. Understanding these will help you see where your money is going.

1. Concrete Thickness & Strength

A standard patio or walkway is usually 4 inches thick. A driveway that needs to support cars and trucks requires 5 to 6 inches. Foundations for homes or large barns will be even thicker and engineered to specific load-bearing requirements. Thicker concrete means more material and often more labor, directly increasing the cost. We use a minimum of 3000 PSI (pounds per square inch) strength concrete for most projects, but higher strength mixes are available for heavy-duty applications at a higher cost.

2. Site Preparation & Grading

Is your project site a level, clear patch of grass, or is it a sloped area covered in roots and rocks? The amount of work required to prepare the sub-base is a major cost variable.

• Grading: We must ensure the ground is level and properly sloped for drainage.
• Base Material: A compacted base of crushed stone (like limerock here in Florida) is crucial for a stable slab that won't crack.
• Clearing: Removing trees, stumps, shrubs, and large roots adds labor and disposal costs.

3. Demolition & Removal

If we're replacing an old, cracked driveway or patio, the cost includes breaking up the old concrete, loading it, and hauling it away for disposal. This demolition work is labor-intensive and adds a significant amount to the total project cost, often $3 to $6 per square foot on top of the new installation price.

4. Reinforcement

For most projects in Florida, reinforcement is essential to control cracking and add strength.

• Wire Mesh: A common, cost-effective option for light-duty slabs like patios and sidewalks.
• Rebar (Steel Rods): Necessary for driveways, foundations, and any slab supporting significant weight. It costs more than mesh but provides far superior structural integrity.
• Fiber Mesh: Tiny synthetic fibers mixed into the concrete to provide secondary, multi-directional reinforcement. It's great for reducing surface shrinkage cracks.

5. Finish Type

The finish you choose affects both the look and the final labor cost.

• Broom Finish: The standard, non-slip texture for most driveways, sidewalks, and patios. This is the baseline cost.
• Trowel/Smooth Finish: Ideal for garage floors or interior spaces. It requires more time and skill to achieve a perfectly smooth surface.
• Stamped & Decorative Concrete: This involves pressing patterns into the concrete to mimic stone, brick, or wood. It's a specialized skill that costs significantly more but delivers a high-end look.
• Exposed Aggregate: This finish reveals the natural stones in the concrete mix for a unique, durable texture. It also requires extra steps and materials.

6. Site Accessibility

Can we get a large ready-mix truck right up to the pour site? If not, we may need to use wheelbarrows or a concrete pump. Pumping concrete adds a setup fee and per-yard cost, which can add several hundred to over a thousand dollars to a job, depending on its size. Tight backyards in communities like The Villages or On Top of the World can sometimes present these challenges.

Ballpark Costs by Project Type in Marion County

• Concrete Driveway Replacement: Typically $10 to $19 per square foot. This higher range accounts for the 5-6 inch thickness, rebar reinforcement, and the cost of tearing out and disposing of the old driveway.
• Concrete Patio: Expect to pay $11 to $20+ per square foot. The range is wide because patios often involve more decorative finishes, colors, or complex shapes compared to a simple slab.
• Basic Concrete Slab (Shed, HVAC): For a simple 4-inch concrete slab with a broom finish and easy access, costs are often on the lower end, around $9 to $15 per square foot.
• Sidewalks & Walkways: Usually $12 to $22 per square foot. While small in total area, the narrow forming and finishing work can increase the per-foot labor cost compared to a large, open slab.

Ready-Mix Material vs. Fully Installed Cost

It's crucial to understand the difference here. When you hear a price "per yard," people are often talking about just the material from the ready-mix plant.

• Material Only: In the Ocala/Wildwood area, a cubic yard of concrete delivered by truck costs roughly $150 - $200. This price doesn't include any labor. You just get a truck full of wet concrete.
• Fully Installed: This is the "turnkey" price from a contractor like CSP Concrete. It includes the concrete material, formwork, grading, base preparation, reinforcement, pouring, finishing, cleanup, and our company's license, insurance, and expertise. This is the all-in price you'll actually pay.

Hiring a licensed and insured contractor ensures the job is done right, to code, and with protection for you and your property.

Local Ocala & Marion County Cost Factors

Working in Central Florida presents unique considerations. Our sandy soil requires proper compaction and a solid base to prevent slabs from settling or cracking. Marion County and the City of Ocala also have building codes and permit requirements for many projects, especially larger driveways and foundations. As a licensed local contractor (Marion County #18069), we handle all necessary permits, ensuring your project is compliant from start to finish. Our experience working throughout the area, from Silver Springs to Dunnellon and The Villages, means we know the ground and the regulations.

Frequently Asked Questions

How much does concrete cost in Ocala?

For a fully installed project in 2026, expect to pay between $9 and $18 per square foot for a standard 4-inch slab. The final price depends on thickness, site prep, reinforcement, and finish type.

What is the average cost of a 20x20 concrete slab?

A 20x20 foot (400 sq ft) concrete slab in the Ocala area typically costs between $3,800 and $7,000 installed. This estimate is for a standard 4-inch slab with a broom finish and good site access.

How much is 1 yard of concrete in Florida?

The material cost for one cubic yard of ready-mix concrete delivered is about $150 to $200. This does not include any labor, forming, finishing, or site preparation, which make up the bulk of the total project cost.

Is pouring a concrete patio cheaper than pavers?

Initially, a standard broom-finish concrete patio is often less expensive than installing pavers. However, high-end decorative or stamped concrete can cost as much or more than pavers. Concrete offers a solid, durable surface with fewer joints for weeds to grow through.

How much is concrete per square foot in Florida?

Across Florida, the installed price for a standard 4-inch concrete slab generally ranges from $9 to $18 per square foot. Local market conditions, material costs, and the specific details of your project will determine the exact price.

Ready to get a firm, accurate price for your concrete project? As a licensed and insured local contractor, CSP Concrete provides detailed, no-pressure estimates. We'll come to your property in Ocala, Belleview, The Villages, or anywhere in Marion County, assess the site, and give you a written quote you can count on. Call us today at (321) 239-6046 or request your free estimate online.